Parkside IAN 406333 Manual


Læs nedenfor 📖 manual på dansk for Parkside IAN 406333 (8 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 8 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/8
3 GB/IE/NI
List of pictograms used
Observe the warnings and safety information!
Risk of fatal injury and accidents for infants and children!
Persons required for assembly: 1
Max.
50 kg Maximum load per shelf: 50 kg
Always wear work gloves.
Assembly time: approx. 15 minutes
Correct
Incorrect
Direction of assembly
Press
Bend the component by 180°.
Safety information
Instructions for use
4 Tier Shelving Unit
Introduction
We congratulate you on the purchase of your new product. You have chosen
a high quality product. Familiarise yourself with the product before using it
for the fi rst time. In addition, please carefully refer to the operating instruc-
tions and the safety advice below. Only use the product as instructed and
only for the indicated fi eld of application. Keep these instructions in a safe
place. If you pass the product on to anyone else, please ensure that you
also pass on all the documentation with it.
Intended use
The product is intended for storing objects. This product is only intended for
private use and is not intended for commercial use. Any use not described
above or product modifi cation is prohibited and can result in injuries and
product damage. The manufacturer assumes no liability for damage result-
ing from improper use.
Technical data
Dimensions: approx. 75 x 30 x 150 cm (B x D x H)
Load per shelf: max. 50 kg
Number of shelves: 4
Material: galvanised steel; HDF shelves
Safety notes
RISK OF FATAL INJURY AND ACCI-
DENTS FOR INFANTS AND CHILDREN! Never leave
children unattended with the packaging material or the prod-
uct. There is a risk of suff ocation. Keep children away from the product.
Keep the packaging material and small parts supplied out of the reach
of children. Otherwise there is a risk of suff ocation!
This product is not a climbing frame!
CAUTION! RISK OF INJURY! Make sure that all parts are undam-
aged and correctly assembled. Improper assembly may result in injury.
Damaged parts could impact safety and function.
Max.
50 kg
Do not load the individual shelves with more than 50 kg. The
indicated maximum load per shelf refers to an even weight
distribution across the entire surface.
Weight must be distributed evenly on the product to prevent it from
tipping over.
We recommend having the product assembled by a skilled person.
Do not sit or stand on the product.
Only set up the product on a secure, level surface.
Check the stability of the product before use.
Always wear work gloves and be careful when handling
sharp or pointy parts.
Do not strike the product with blunt objects.
Routinely verify that the product is solid and stable.
Not suitable for storing fl ammable or corrosive materials.
Never store hot objects inside the product (e.g. recently used barbecues,
blowtorches, irons etc.).
Not suitable for storing food.
The product must be anchored to a wall for safety reasons (see fi g. 7
and 8). The mounting materials required are not included in the delivery.
Before anchoring the product to the wall, check which fasteners are suit-
able for your wall.
RISK OF FATAL INJURY! Please be sure not to
drill into any electrical wiring, gas or water lines inside the wall. If nec-
essary, carry out checks with a wire, pipe and stud detector before you
drill into a wall.
Keep the assembly instructions for future reference.
Before assembly
If parts are missing or damaged, please contact your local retailer and
have your receipt ready. Always specify the IAN.
This product may contain some sharp parts. Therefore always wear work
gloves.
Due to deviations, the actual assembled size may vary slightly from the
specifi ed dimensions.
Assembly
Please be sure not to damage the product when opening the packaging
with a knife or other sharp object.
Remove the individual product parts from the packaging.
Check that all parts are present.
Assemble the product as shown in fi gures 1 to 6.
Note: The product can be assembled upright or horizontal.
Insert the crosspieces D at the locations provided, as shown in Figure
4. First, bend the fastener by 90 ° in order to attach the crosspiece D
to the transverse beam C1. Then, bend the fasteners by 180 °, as shown,
to fi x the components in place. Use a fl at-head screwdriver to do so.
406333_2207_V1.0_par_Schwerlastregal_content_GB.indd 3
406333_2207_V1.0_par_Schwerlastregal_content_GB.indd 3
406333_2207_V1.0_par_Schwerlastregal_content_GB.indd 3
406333_2207_V1.0_par_Schwerlastregal_content_GB.indd 3406333_2207_V1.0_par_Schwerlastregal_content_GB.indd 3 22.12.22 13:40
22.12.22 13:40
22.12.22 13:40
22.12.22 13:4022.12.22 13:40


Produkt Specifikationer

Mærke: Parkside
Kategori: Ikke kategoriseret
Model: IAN 406333

Har du brug for hjælp?

Hvis du har brug for hjælp til Parkside IAN 406333 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Parkside Manualer

Parkside

Parkside IAN 327414 Manual

8 December 2024
Parkside

Parkside WWS-GLK9-Y02 Manual

16 November 2024
Parkside

Parkside PAMFW 1 Manual

4 Oktober 2024
Parkside

Parkside HG00962B Manual

23 September 2024
Parkside

Parkside PWZS 2 A1 Manual

22 September 2024
Parkside

Parkside PSMW 1 A1 Manual

16 September 2024
Parkside

Parkside HG02796 Manual

10 September 2024
Parkside

Parkside PEXS 270 B2 Manual

9 September 2024
Parkside

Parkside PDAV 3 A1 Manual

9 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Atlona

Atlona AT-DVIF30S-IR Manual

29 December 2024
Atlona

Atlona AT-PRO3HD66M Manual

29 December 2024
Atlona

Atlona AT-3GSDI500 Manual

29 December 2024
BlueBuilt

BlueBuilt BBMAG2M Manual

29 December 2024
Atlona

Atlona AT-3GSDI-14 Manual

28 December 2024
Atlona

Atlona AT-COMP10SS Manual

28 December 2024
Atlona

Atlona AT-2VGA300SL Manual

28 December 2024
Atlona

Atlona AT-HD-V216 Manual

28 December 2024
Atlona

Atlona AT-VGA11S Manual

28 December 2024
True

True TC900 Manual

28 December 2024