Black Diamond Alpine Carbon Z Manual


Læs nedenfor 📖 manual på dansk for Black Diamond Alpine Carbon Z (17 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 8 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/17
WARNING [EN]
Trekking Poles and Z-poles are for hiking and
trekking use only. The strength of aluminum and
carbon fiber is compromised by dents, gouges,
scratches, fractures, and chipping which may result
in catastrophic structural failure. If the trekking
pole has suffered any impact, carefully inspect its
surface for these signs of damage. Lightweight
trekking poles are made to be lightweight, and
will not withstand excessive forces if previously
damaged or if the forces are applied beyond
structural limits. Ultralight carbon fiber poles are
more susceptible to damage than other poles and
require frequent inspection. Failure to follow these
warnings may result in catastrophic failure of the
trekking poles, causing serious injury or death.
INSTRUCTIONS FOR USE
ѥKeep instructions for future reference.
RAPID DEPLOYMENT SYSTEM
The Rapid Deployment System is linked to a concealed
inner cord and speed cone within each shaft section
in a foldable trekking pole. The push-button locking
mechanism is located just below the grip on fixed length
models and below the numbered FlickLock adjustment
section on FlickLock models.
DEPLOYING
Ensure the basket is unclipped from any other shafts.
1. Grab the grip and the first shaft section, and pull
them away from each other. The pole will snap into
place and lock.
2. Check that the push-button has snapped
completely out and the pole is locked without gaps
at the joints.
COLLAPSING
1. Press the button and slide the grip toward the pole
tip.
2. Pull the shafts apart at each joint, located at the
seam between each shaft section.
3. Fold the poles into a compact “Z” shape.
4. Snap the lower shaft’s basket clip onto the upper or
middle shaft for secure storage.
If the pole has a FlickLock, open the lever arm and fully
collapse the pole to minimize its folded length.
ADJUSTING TENSION
The inner cord that connects Z-Pole shaft sections
may require adjustment before use and will require
adjustment over time as the inner cord stretches in the
uppermost shaft section. This play can be removed by
increasing the inner cord tension.
1. Press the push-button release, and pull ONLY the
lowest joint apart.
2. Hold both ends of the tensioner (located between
the middle and lower shafts) and turn it clockwise to
tighten or counter-clockwise to loosen.
3. Turn the tensioner one-half to one full turn, and
re-deploy the pole to check that you’ve removed
the play.
NOTE: If you cannot deploy the pole (the button won’t
pop back out), you have over-tightened it. Loosen
slightly and tr y again. Wh en tension is adjusted
correctly, the pole should lock easily yet have no play
in the shafts.
Avoid damage to the pole shaft around the pin by
keeping cord tension to a minimum
Inspection your poles prior to each use around the
pin-hole. Damaged poles should not be used.
NEVER loosen the tensioner completely unless
replacing a lower section.
FLICKLOCK®
The patented FlickLock is an external camming
mechanism which, when closed, squeezes the pole
shafts together to form a joint stronger than the tubing
itself. To open:
1. Hold the pole above the FlickLock to prevent the
pole from rotating while pushing the cam lever open
with your thumb.
2. Adjust pole to the desired length
3. “Snap” close the lever firmly.
ADJUSTING TENSION
The FlickLock requires correct tensioning to per form
properly. If slipping of the lower section occurs then
open the lever and tighten the adjustment screw about
a quarter to a half turn or until the mechanism does not
allow the shaft to slip once the lever is closed.
If the lever becomes too difficult to snap shut, loosen
the screw.
CHANGING TECH TIPS
Z-Poles come with rubber tips installed and optional
carbide tips. Rubber tips should be replaced once any
part of the metal core starts to show.
To remove:
1. Using fingers or pliers, twist forcefully counter-
clockwise and un-screw until they fall out of the
baskets.
To install new tips:
2. Twist by hand or with pliers, clockwise, for 3-4
clicks and very snug. Rubber tips should bulge
when they are completely tightened.
Some models of trekking poles come with Flex Tips. To
remove, the Flex Tip needs to be heated (submerge in
boiling water) and pulled off with pliers. Firmly push the
new Flex Tip onto the tip of the pole.
BASKETS
To at t ac h a ba sket : Push the ba sket and turn
clo ckwise until se cured against th e upper stop,
spinning freely.
To remove a basket: Pull the basket and twist coun-
terclockwise.
(See accompanying illustrations)
CARE AND MAINTENANCE
To clean cork grips:
1. Use fine, waterproof sandpaper and ordinary hand
soap.
2. Wet the grip and sand thoroughly.
3. Apply soap to the sandpaper and gently rub the grip.
4. Rinse and let dry.
INSPECTION & STORAGE
Before and after each use:
Make sure nothing is deformed or broken.
Check to see that the adjustment mechanisms open
and close smoothly and are tensioned properly.
If difficult to open or close: apply a drop of oil on the
lever pin and another underneath the lever where it
rotates on the housing.
If the poles get wet during use: release the tension
cord (with the push button), collapse the pole and
allow to dry completely before storage.
NOTE: Store the FlickLock mechanisms for long
periods with the tension released. Replacement parts
may be obtained from your local Black Diamond dealer
or directly from Blackdiamondequipment.com.
(See accompanying illustrations)
LIMITED WARRANTY
For one year following purchase unless otherwise
indicated by law, we will warrant to the original retail
buyer only that our products are free from defects in
material and workmanship as originally sold. If you
receive a defective product, return it to us and we will
replace it subject to the following conditions: We do not
warrant products which show normal wear and tear or
that have been used or maintained improperly, modified
or altered, or damaged in any manner.
AVERTISSEMENT [FR]
Les bâtons de randonnée Trekking Poles
et Z-poles sont conçus pour une utilisation
en randonnée et en trek uniquement. Les
bosses, les rainures, les éraflures, les fissures
et les écailles compromettent la résistance
de l’aluminium et de la fibre de carbone
et peuvent entraîner des défaillances
structurelles. Si le bâton de randonnée a é
soumis à un quelconque impact, inspectez
soigneusement sa surface afin de repérer
tout signe de térioration. Les bâtons de
randonnée légers sont conçus pour être gers
et ne résisteront pas à des forces excessives
s’ils ont subi des dommages antérieurs ou si
les forces appliquées dépassent leurs limites
structurelles. Les bâtons ultra légers en
fibre de carbone sont davantage sujets aux
détériorations que les autres bâtons et exigent
d’être inspectés fréquemment. Le non-respect
des psents avertissements peut causer
une défaillance des bâtons de randonnée, et
entraîner des blessures graves ou la mort.
NOTICE D’UTILISATION
ѥVeuillez conserver la notice pour consultation
ultérieure.
SYSTÈME À DÉPLOIEMENT RAPIDE
Le système à déploiement rapide est relié à un ble
interne dissimulé et à un cône à déploiement rapide
intégrés dans chaque brin du bâton de randonnée
repliable. Le bouton-poussoir est situé juste sous la
poignée sur les modèles à longueur fixe et sous le brin à
glage FlickLock numéroté sur les moles FlickLock.
PLIAGE
Vérifiez si la rondelle d’arrêt n’est pas attachée à un
quelconque brin.
1. Saisissez la poignée et le brin supérieur puis tirez
simultanément de part et d’autre. Leton se met
en place d’un coup sec et se verrouille.
2. Assurez-vous que le bouton-poussoir est
comptement enclenché et que le bâton est
verrouil de manre parfaitement jointive aux
jonctions.
REPLIAGE
1. Appuyez sur le bouton et faites coulisser la poignée
en direction de la pointe du bâton.
2. Tirez sur les brins de part et d’autre de chaque
jonction séparant chaque brin.
3. Repliez les bâtons de manre à former un “Z”
compact.
4. Clippez la rondelle d’art du brin inférieur sur
le brin supérieur ou médian pour une meilleure
curité de stockage.
Si le bâton possède un FlickLock, ouvrez le bras du
levier et repliez complètement le bâton pour réduire sa
longueur repliée.
AJUSTEMENT DU SERRAGE
Le câble interne qui relie les brins de votre bâton Z-Pole
peut nécessiter d’un ajustement avant utilisation et
exige un ajustement dans le temps car le câble interne
peut gèrement se détendre dans le brin supérieur.
Vous pouvez redier à ce jeu en augmentant le degré
Z-POLE
TREKKING
POLES
© Black Diam ond Equipment, Ltd. 2021
M10644_GWEB
North America: Black Diamond Equipment, Ltd.
2084 East 3900 South
Salt Lake City, UT 84124
Europe: Black Diamond Equipment
Hans-Maier-Straße 9
6020, Innsbruck, Austria
www.BlackDiamondEquipment.com


Produkt Specifikationer

Mærke: Black Diamond
Kategori: Ikke kategoriseret
Model: Alpine Carbon Z

Har du brug for hjælp?

Hvis du har brug for hjælp til Black Diamond Alpine Carbon Z stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Black Diamond Manualer

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Elektron

Elektron Overbridge Manual

26 November 2024
Elektron

Elektron Sidstation Manual

26 November 2024
SoundTube

SoundTube IPD-RS82-EZ Manual

26 November 2024
Kramer

Kramer 4x1VB Manual

26 November 2024
Kramer

Kramer RC-63A Manual

26 November 2024
SoundTube

SoundTube IPD-HP82-EZ Manual

26 November 2024
Kramer

Kramer RK-KVM-1U-PP3 Manual

26 November 2024
Gioteck

Gioteck VX-2 (PS3) Manual

26 November 2024