Omron RS3 Intelli IT Manual

Omron Blodtryksmåler RS3 Intelli IT

Læs nedenfor 📖 manual på dansk for Omron RS3 Intelli IT (2 sider) i kategorien Blodtryksmåler. Denne guide var nyttig for 33 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF

Side 1/2

Introduction

Important Safety Information

1. Know Your Monitor

2. Preparation

3. Using Your Monitor

4. Other Settings

5. Error Messages and Troubleshooting

6. Maintenance

7. Specifications

8. Limited Warranty

9. Guidance and Manufacturer’s Declaration

Thank you for purchasing the RS3 Intelli IT Automatic Wrist Blood

Pressure Monitor. This blood pressure monitor is to be worn on your

wrist.

This blood pressure monitor uses the oscillometric method of blood

pressure measurement. When the cuff inflates, this monitor senses

the pressure pulsations of the artery underneath the cuff. The pulses

are called oscillometric pulses. The electronic pressure sensor

displays a digital reading of blood pressure.

Safety Instructions

This instruction manual provides you with important information

about the RS3 Intelli IT Automatic Wrist Blood Pressure Monitor. To

ensure the safe and proper use of this monitor, READ and

UNDERSTAND all of the safety and operating instructions. If you do

not understand these instructions or have any questions, contact

your OMRON retail outlet or distributor before attempting to use this

monitor. For specific information about your own blood pressure,

consult with your physician.

Intended Use

This device is a digital monitor intended for use in measuring blood

pressure and pulse rate in adult patient population with wrist

circumference ranging from 13.5 cm to 21.5 cm. This monitor

detects the appearance of irregular heartbeats during measurement

and gives a warning signal with readings. It is mainly designed for

general household use.

Receiving and Inspection

Remove this monitor from the packaging and inspect for damage. If

this monitor is damaged, DO NOT USE and consult with your

OMRON retail outlet or distributor.

Please read the Important Safety Information in this instruction

manual before using this monitor.

Please follow this instruction manual thoroughly for your safety.

Please keep for future reference. For specific information about your

own blood pressure, CONSULT WITH YOUR PHYSICIAN.

Warning

Indicates a potentially hazardous situation

which, if not avoided, could result in death or

serious injury.

• DO NOT use this monitor on infants, toddlers, children or

persons who cannot express themselves.

• DO NOT adjust medication based on readings from this blood

pressure monitor. Take medication as prescribed by your

physician. ONLY a physician is qualified to diagnose and treat

high blood pressure.

• DO NOT use this monitor on an injured wrist or a wrist under

medical treatment.

• DO NOT apply the wrist cuff on your wrist while on an

intravenous drip or blood transfusion.

• DO NOT use this monitor in areas containing high frequency

(HF) surgical equipment, magnetic resonance imaging (MRI)

equipment, computerized tomography (CT) scanners. This

may result in incorrect operation of the monitor and/or cause

an inaccurate reading.

• DO NOT use this monitor in oxygen rich environments or near

flammable gas.

• Consult with your physician before using this monitor if you

have common arrhythmias such as atrial or ventricular

premature beats or atrial fibrillation; arterial sclerosis; poor

perfusion; diabetes; pregnancy; pre-eclampsia or renal

disease. NOTE that any of these conditions in addition to

patient motion, trembling, or shivering may affect the

measurement reading.

• NEVER diagnose or treat yourself based on your readings.

ALWAYS consult with your physician.

• This product contains small parts that may cause a choking

hazard if swallowed by infants, toddlers or children.

Data Transmission

• This product emits radio frequencies (RF) in the 2.4 GHz

band. DO NOT use this product in locations where RF is

restricted, such as on an aircraft or in hospitals. Turn off the

Bluetooth feature in this monitor and remove batteries when

in RF restricted areas.

Battery Handling and Usage

• Keep batteries out of the reach of infants, toddlers or

children.

Caution

Indicates a potentially hazardous situation

which, if not avoided, may result in minor or

moderate injury to the user or patient, or cause

damage to the equipment or other property.

• Stop using this monitor and consult with your physician if

you experience skin irritation or discomfort.

Automatic Wrist Blood

Pressure Monitor

RS3 Intelli IT (HEM-6161T-E)

Instruction Manual

IM-HEM-6161T-E-EN-01-09/2018

4602352-2A

Table of Contents

Introduction

Important Safety Information

• Consult with your physician before using this monitor on a

wrist where intravascular access or therapy, or an arterio-

venous (A-V) shunt, is present because of temporary

interference to blood flow which could result in injury.

• Consult with your physician before using this monitor if you

have had a mastectomy.

• Consult with your physician before using this monitor if you

have severe blood flow problems or blood disorders as cuff

inflation can cause bruising.

• DO NOT take measurements more often than necessary

because bruising, due to blood flow interference, may occur.

• ONLY inflate the wrist cuff when it is applied on your wrist.

• Remove the wrist cuff if it does not start deflating during a

measurement.

• DO NOT use this monitor for any purpose other than

measuring blood pressure.

• During measurement, make sure that no mobile device or any

other electrical device that emits electromagnetic fields is

within 30 cm of this monitor. This may result in incorrect

operation of the monitor and/or cause an inaccurate reading.

• DO NOT disassemble or attempt to repair this monitor or

other components. This may cause an inaccurate reading.

• DO NOT use in a location where there is moisture or a risk of

water splashing this monitor. This may damage this monitor.

• DO NOT use this monitor in a moving vehicle such as in a car.

• DO NOT drop or subject this monitor to strong shocks or

vibrations.

• DO NOT use this monitor in places with high or low humidity

or high or low temperatures. Refer to chapter 7.

• Ensure this monitor is not impairing blood circulation by

observing the wrist while measurement is occurring.

• DO NOT use this monitor in high-use environments such as

medical clinics or physician offices.

• DO NOT use this monitor with other medical electrical (ME)

equipment simultaneously. This may result in incorrect

operation of the monitor and/or cause an inaccurate reading.

• Avoid bathing, drinking alcohol or caffeine, smoking,

exercising and eating for at least 30 minutes before taking a

measurement.

• Rest for at least 5 minutes before taking a measurement.

• Remove tight-fitting, thick clothing and any accessories from

your wrist while taking a measurement.

• Remain still and DO NOT talk while taking a measurement.

• ONLY use this monitor on persons whose wrist

circumference is within the specified range of the cuff.

• Ensure that this monitor has acclimated to room temperature

before taking a measurement. Taking a measurement after an

extreme temperature change could lead to an inaccurate

reading. OMRON recommends waiting for approximately 2

hours for the monitor to warm up or cool down when the

monitor is used in an environment within the temperature

specified as operating conditions after it is stored either at

the maximum or at the minimum storage temperature. For

additional information of operating and storage/transport

temperature, refer to chapter 7.

• DO NOT crease the wrist cuff excessively.

• Read and follow the “Correct Disposal of This Product” in

chapter 9 when disposing of the device and any used

accessories or optional parts.

• DO NOT use this monitor after the durable period has ended.

Refer to chapter 7.

Data Transmission

• DO NOT replace batteries while your reading is being

transferred to your smart device. This may result in the

incorrect operation of this monitor and failure to transfer your

blood pressure data.

Battery Handling and Usage

• DO NOT insert batteries with their polarities incorrectly

aligned.

• ONLY use 2 “AAA” alkaline batteries with this monitor. DO

NOT use other types of batteries. DO NOT use new and used

batteries together. DO NOT use different brands of batteries

together.

• Remove batteries if this monitor will not be used for a long

period of time.

• If battery fluid should get in your eyes, immediately rinse with

plenty of clean water. Consult with your physician

immediately.

• If battery fluid should get on your skin, wash your skin

immediately with plenty of clean, lukewarm water. If irritation,

injury or pain persists, consult with your physician.

• DO NOT use batteries after their expiration date.

• Periodically check batteries to ensure they are in good

working condition.

• ONLY use batteries specified for this monitor. Use of

unsupported batteries may damage and/or may be hazardous

to this monitor.

1.1 Contents

Monitor, 2 “AAA” alkaline batteries, storage case, instruction manual,

setup instructions

1.2 Monitor

a. Wrist cuff

(Wrist circumference 13.5 cm to 21.5 cm)

b. Display

c. Battery compartment

d. [Connection] button

e. [START/STOP] button

1. Know Your Monitor

1.3 Display and Symbols

2013 ESH/ESC* Guidelines for the management of

arterial hypertension

Definitions of hypertension by office and home blood pressure levels

These ranges are from statistical values for blood pressure.

Warning

• NEVER diagnose or treat yourself based on your readings.

ALWAYS consult with your physician.

2.1 Installing Batteries

1. Push down the hook of the battery

cover and pull downward.

2. Insert 2 “AAA” alkaline batteries as

indicated in the battery compartment.

ASystolic blood pressure reading

BDiastolic blood pressure reading

Cuff wrap guide symbol (OK)

Appears if the wrist cuff is wrapped around the wrist

correctly while taking a measurement. It also

appears when viewing past readings.

Cuff wrap guide symbol (loose)

Appears if the wrist cuff is not wrapped around the

wrist correctly while taking a measurement. It also

appears when viewing past readings.

Heartbeat symbol

Flashes while taking a measurement.

Appears if your systolic blood pressure is 135

mmHg or above and/or the diastolic blood pressure

is 85 mmHg or above.

EDeflation symbol

Appears during cuff deflation.

Bluetooth ON symbol

Appears when Bluetooth is enabled.

Bluetooth OFF symbol

Appears when Bluetooth is disabled.

Sync symbol

Flashes/appears when your data needs to be

transferred because the stored memory is either

almost, or completely full. Once you pair your

monitor with a smart device, transfer your readings

immediately before the monitor deletes the oldest

readings. Up to 30 readings can be stored in the

internal memory.

Battery symbol (low)

Flashes when batteries are low.

Battery symbol (depleted)

Appears when batteries are depleted.

Irregular heartbeat symbol

Appears along

with readings

when an irregular

rhythm is detected

2 or more times

during a

measurement.

An irregular

heartbeat rhythm

is defined as a

rhythm that is 25% less or 25% more than the

average rhythm detected while your monitor is

measuring blood pressure. If it continues to appear,

we recommend you to consult with and follow the

directions of your physician.

JPulse display / Memory number

Pulse rate appears after the measurement.

Office Home

Systolic Blood

Pressure ≥ ≥ 140 mmHg 135 mmHg

Diastolic Blood

Pressure ≥ ≥ 90 mmHg 85 mmHg

off

Irregular Heartbeat

Normal Heartbeat

Pulse

Blood pressure

Short Long

Pulse

* European Society of Hypertension (ESH) and European Society

of Cardiology (ESC).

2. Preparation

3. Close the battery cover.

Note

• When the “ ” symbol flashes on the display, it is recommended

you replace batteries.

• To replace batteries, turn your monitor off and remove all batteries.

Then replace with 2 new alkaline batteries at the same time.

• Replacing batteries will not delete previous readings.

• The supplied batteries may have a shorter life than new batteries.

• Disposal of used batteries should be carried out in accordance

with local regulations.

• As soon as batteries are correctly installed, “P” flashes on the

display to start pairing. To pair your monitor, refer to section 2.2. If

your monitor has already been paired with your smart device when

batteries are installed, "O" will flash. If it flashes, transfer your

readings.

2.2 Pairing Your Monitor with a Smart Device

Review the list of compatible smart devices at

www.omronconnect.com/devices/

1. Enable Bluetooth on your smart device.

2. Download and install the free “OMRON connect” app

onto your smart device.

If you already have the “OMRON connect” app, open the app

and add your new monitor.

3. Open the app on your smart device and follow the

instructions.

4. Confirm that your monitor is

connected successfully.

When your monitor is connected

successfully to your smart device, the

“OK” symbol appears.

Note

• If the “Err” symbol appears, follow the

instructions in the “OMRON connect”

app.

• Your monitor automatically turns off

after 10 seconds without any

operations.

• Any readings currently saved in the memory of your monitor

are automatically transferred to the app after successful

completion of the pairing process.

• Please be aware that OMRON will not be responsible for the

loss of data and/or information in the app.

• “OMRON connect” is the only app that we recommend to use

with your monitor to transfer data correctly.

2.3 Blood Pressure Measurement Tips

To help ensure an accurate reading, follow these directions:

• Stress raises blood pressure. Avoid taking measurements during

stressful times.

• Measurements should be taken in a quiet place.

• It is important to take measurements at same times each day.

Taking measurements in the morning and in the evening is

recommended.

• Remember to have a record of your blood pressure and pulse

readings for your physician. A single measurement does not

provide an accurate indication of your true blood pressure.

Please use the Blood Pressure Diary to keep records of several

readings over a certain period of time. To download PDF files of

the diary, visit www.omron-healthcare.com.

Caution

• Avoid bathing, drinking alcohol or caffeine, smoking, exercising

and eating for at least 30 minutes before taking a measurement.

• Rest for at least 5 minutes before taking a measurement.

2.4 Applying the Wrist Cuff

Note

• Following steps are for applying the wrist cuff to your left wrist.

When you take a measurement on your right wrist, apply the wrist

cuff using the same steps as on your left wrist.

• The blood pressure can differ between the right wrist and the left

wrist, and the measured blood pressure values can be different.

OMRON recommends to always use the same wrist for

measurement. If the values between both wrists differ

substantially, please check with your physician as to which wrist to

use for your measurements.

Caution

• Remove tight-fitting, thick clothing and any accessories from your

wrist while taking a measurement.

1. Apply the wrist cuff to your left

wrist.

Roll up sleeve. Make sure your

sleeve is not rolled up too tightly on

your arm. This may constrict the flow

of blood in your arm.

2. Put your wrist through the cuff loop.

Your palm and monitor display should both

face upward.

Wrist cuff

3. Position the wrist cuff leaving a

clearance of 1 to 2 cm between

the cuff and the bottom of your

palm.

4. Wrap the wrist cuff firmly around

your wrist. Do not apply over

clothing.

Check to make sure that there is no gap

between your wrist and the cuff.

Note

• Make sure the wrist cuff does not

cover the protruding part of the wrist

bone on the outside of your wrist.

2.5 Sitting Correctly

To take a measurement, you

need to be relaxed and

comfortably seated in a room with

a comfortable temperature. Place

your elbow on the table to support

your arm.

• Sit in a chair with your legs

uncrossed and your feet flat on

the floor.

• Sit with your back and arm

being supported.

• Your monitor must be

approximately the same level

as your heart. If the monitor is

too high above your heart, your blood pressure will be artificially

low. If the monitor is too low below your heart, your blood pressure

will be artificially high.

• Relax your wrist and hand. Do not bend your wrist back, clench

your fist, or bend your wrist forward.

3.1 Taking a Measurement

Note

• To stop the measurement, press the [START/STOP] button once

to deflate the wrist cuff.

Caution

• DO NOT use this monitor with other medical electrical (ME)

equipment simultaneously. This may result in incorrect operation

of the monitor and/or cause an inaccurate reading.

• Remain still and DO NOT talk while taking a measurement.

1. Press the [START/STOP] button.

All symbols appear on the display before starting the

measurement.

2. Remain still and do not move or talk until the entire

measurement process is completed.

As the cuff inflates, your monitor automatically determines your

ideal inflation level. This monitor detects your blood pressure

and pulse rate during inflation.

The “ ” symbol flashes at every heartbeat.

Note

• The “ ” symbol appears if the wrist cuff is wrapped

around the wrist correctly.

• When the “ ” symbol is displayed, the wrist cuff is not

applied correctly. Press the [START/STOP] button to turn

your monitor off, then apply the cuff correctly.

After your monitor has detected your blood pressure and pulse

rate, the cuff automatically deflates. Your blood pressure and

pulse rate are displayed.

If either the systolic or the diastolic reading is high (refer to

section 1.3), the “ ” symbol appears.

3. Press the [START/STOP] button to turn your monitor off.

Note

• Your monitor will automatically turn off after 2 minutes.

• Wait 2-3 minutes between measurements. The wait time

allows the arteries to decompress and return to their pre-

measurement form. You may need to increase the wait time

depending on your individual physiological characteristics.

1 to 2 cm

3. Using Your Monitor

START INFLATING COMPLETED

Produkt Specifikationer

Mærke:	Omron
Kategori:	Blodtryksmåler
Model:	RS3 Intelli IT

Har du brug for hjælp?

Hvis du har brug for hjælp til Omron RS3 Intelli IT stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Blodtryksmåler Omron Manualer

Omron RS1 Manual

3 Oktober 2024

Omron BP742 Manual

14 September 2024

Omron M10 IT Manual

2 September 2024

Omron X2 Smart+ HEM-7146T2-ESL Manual

1 September 2024

Omron M1 Compact Manual

30 August 2024

Omron BP6350 Manual

30 August 2024

Omron CD-CS9 Manual

30 August 2024

Omron M 400 - HEM-7131 Manual

25 August 2024

Omron M 400 IT - HEM-7131U Manual

24 August 2024

Omron M24-7 ABPM Manual

24 August 2024

Blodtryksmåler Manualer

Nyeste Blodtryksmåler Manualer

Archos Blood Pressure Monitor - 183 Manual

15 December 2024

ADE Pressure BPM 1401 Manual

15 December 2024

Oregon Scientific BPW128 Manual

15 December 2024

Oregon Scientific BPW211 Manual

15 December 2024

Oregon Scientific BPW120 Manual

15 December 2024

ADE Pressure BPM 1400 Manual

15 December 2024

Oregon Scientific BPW221 Manual

15 December 2024

Mx Onda MX-CP2395 Manual

17 November 2024

A&D Medical UB-525 Manual

28 Oktober 2024

Homedics BPA-P200 Manual

28 Oktober 2024