Silverline 633838 Manual
Silverline
Loddemaskine
633838
Læs nedenfor 📖 manual på dansk for Silverline 633838 (1 sider) i kategorien Loddemaskine. Denne guide var nyttig for 32 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere
Side 1/1
633838
GB
Register online: silverlinetools.com
3
GUARANTEE
YEAR
ANS DE GARANTIE
JAHRE GARANTIE
AÑOS DE GARANTÍA
ANNI DI GARANZIA
JAAR GARANTIE
LATA GWARANCJI
silverlinetools com
Version date: 10.01.2018
FR Fer à souder 60 W
DE Lötkolben, 60 W
ES Soldador 60 W
IT Saldatore 60 W
NL Soldeerbout, 60 W
PL Lutownicagrzałkowa60W
Soldering Iron 60W UK
1
2
3
4
Specication
Voltage:............................................................230V~, 50Hz
Frequency:.....................................................................50Hz
Power:.............................................................................60W
Temperature:........................................................480-520°C
Protection Class:..............................................................
Ingress protection:..........................................................IP20
Product Familiarisation
1. Soldering Tip
2. Heating Element
3. Handle
4. Locking Screw
Introduction
Thank you for purchasing this Silverline product. This manual contains
information necessary for safe and effective operation of this product.
This product has unique features and, even if you are familiar with similar
products, it is necessary to read this manual carefully to ensure you fully
understand the instruction. Ensure all users of the product read and fully
understand this manual.
Technical Abbreviations Key
VVolts HertzHz
~Alternating
current W, kW Watt, kilowatt
A °Ampere Degrees
Specic Safety
Electric Soldering Safety
WARNING: This appliance must be placed on a suitable stand when not in
use
WARNING: Do not hang the soldering iron vertically during use. This will
cause heat to rise, which could make the handle too hot to touch and in
extreme circumstances soften or melt the handle. Allowing the iron to hang
down will also place additional strain on the power cable mounting.
WARNING: Only use soldering iron stands suitable for the wattage of your
soldering iron. Do not use high wattage irons with light small soldering iron
stands.
IMPORTANT: Use soldering irons safely. Use promptly when the soldering
iron has reached the required temperature and switch off immediately after
use.
• Soldering appliances become extremely hot during use. Do not touch
any part of the appliance other than the handle
• Switch ‘OFF’ and allow the appliance to cool completely before
attemptingtochangeanyttings
• Do not leave this appliance unattended whilst hot
• Heat may be conducted to hidden areas or materials near to the work
area.Ensurethattherearenoammablematerialsinthevicinityofthe
work area
• Residual heat may cause waste material to ignite, even after the
appliance has been disconnected from the power supply
• Never use these appliances near any kind of fuel tank or gas cylinder
• Soldering with certain materials may result in toxic fumes. Always allow
adequateventilation.Donotuseinconnedspaces
• Some types of solder may contain high proportions of lead. Molten
lead emits toxic fumes, always wear good quality appropriate breathing
protection
• Lead fumes are especially toxic to children, pregnant women and people
with high blood pressure. People at high risk should not be allowed near to the work area
• Always dispose of waste material responsibly
Intended Use
Electric soldering iron for soldering of larger electronic components, wires
and electrical connections.
Unpacking Your Appliance
• Carefully unpack and inspect your new soldering iron. Familiarise
yourself with all its features and functions.
• Ensure that all parts of the appliance are present and in good condition.
If any parts are missing or damaged, have such parts replaced before
attempting to use this appliance.
Before Use
WARNING: Ensure the appliance is disconnected from the power supply
before attaching or changing any accessories, or making any adjustments.
• CheckthattheSolderingTip(1)issecurelyttedbeforeswitchingon.
The soldering tip should be pushed into the Heating Element (2) and
secured by tightening the Locking Screw (4)
Operation
Note: ALWAYS wear eye protection, adequate respiratory and hearing
protection, as well as suitable gloves, when working with this appliance.
• Do not allow the heating element or soldering tip to rest on any surface
that may be damaged by heat
• To operate, connect to mains power supply and allow to reach operating
temperature
• Hold the Soldering Tip (1) against the wire or component to be soldered.
Once hot, add solder to the joint then remove soldering iron
Accessories
• A range of accessories and consumables, including soldering iron tips is
available from your Silverline stockist
• Spare parts can be obtained from toolsparesonline.com
Maintenance
General inspection
• Regularlycheckthatallthexingscrewsaretight
• Inspect the supply cord of the appliance, prior to each use, for damage
or wear. Repairs should be carried out by an authorised Silverline
service centre. This advice also applies to extension cords used with this
appliance
Tip Replacement
WARNING: Always disconnect appliance from power supply and allow to
cool fully before attempting to adjust or replace any part.
• Slacken the Locking Screw (4) and withdraw the Soldering Tip (1)
• Push the replacement soldering tip into the Heating Element (2) and
retighten the Locking Screw
Cleaning
• Keep your appliance clean at all times. Dirt and dust will cause internal
parts to wear quickly, and shorten the appliances’ service life. Clean the
body of your appliance with a soft brush, or dry cloth. If available, use
clean, dry, compressed air to blow through the ventilation holes
• Clean the appliance casing with a soft damp cloth using a mild
detergent. Do not use alcohol, petrol or strong cleaning agents
• Never use caustic agents to clean plastic parts
Contact
For technical or repair service advice, please contact the helpline on (+44)
1935 382 222
Web: silverlinetools.com/en-GB/Support
Address:
Powerbox
Boundary Way
Lufton Trading Estate
Yeovil, Somerset
BA22 8HZ, United Kingdom
Storage
• Store this tool carefully in a secure, dry place out of the reach of children
Disposal
Always adhere to national regulations when disposing of appliances that are
no longer functional and are not viable for repair.
• Do not dispose of appliances, or other waste electrical and electronic
equipment (WEEE), with household waste
• Contact your local waste disposal authority for information on the correct
way to dispose of appliances
Produkt Specifikationer
| Mærke: | Silverline |
| Kategori: | Loddemaskine |
| Model: | 633838 |
Har du brug for hjælp?
Hvis du har brug for hjælp til Silverline 633838 stil et spørgsmål nedenfor, og andre brugere vil svare dig
Loddemaskine Silverline Manualer
3 September 2024
14 August 2024
2 August 2024
31 Juli 2024
26 Juli 2024
26 Juli 2024
25 Juli 2024
25 Juli 2024
6 Juli 2024
13 Marts 2024
Loddemaskine Manualer
- Loddemaskine Ozito
- Loddemaskine RYOBI
- Loddemaskine GYS
- Loddemaskine Güde
- Loddemaskine Denon
- Loddemaskine Nedis
- Loddemaskine Milwaukee
- Loddemaskine Parkside
- Loddemaskine FERM
- Loddemaskine Trotec
- Loddemaskine Einhell
- Loddemaskine Powerfix
- Loddemaskine Mercury
- Loddemaskine Telwin
- Loddemaskine Craftsman
- Loddemaskine Powerplus
- Loddemaskine Westfalia
- Loddemaskine HQ
- Loddemaskine Basetech
- Loddemaskine Fieldmann
- Loddemaskine Velleman
- Loddemaskine Weller
- Loddemaskine Ridgid
- Loddemaskine Monacor
- Loddemaskine Truper
- Loddemaskine Toolcraft
- Loddemaskine Holzmann
- Loddemaskine Steren
- Loddemaskine Yato
- Loddemaskine Cocraft
- Loddemaskine Maestro
- Loddemaskine Cigweld
- Loddemaskine Sievert
- Loddemaskine Epcom
- Loddemaskine Uten
- Loddemaskine CFH
- Loddemaskine Edsyn
- Loddemaskine Mag-Torch
- Loddemaskine UNIMIG
- Loddemaskine Ersa
- Loddemaskine Portasol
- Loddemaskine JBC
- Loddemaskine Hakko
- Loddemaskine Fixpoint
- Loddemaskine Stamos
Nyeste Loddemaskine Manualer
4 December 2024
3 November 2024
19 Oktober 2024
15 Oktober 2024
15 Oktober 2024
15 Oktober 2024
15 Oktober 2024
15 Oktober 2024
15 Oktober 2024
15 Oktober 2024